1、功能说明
    此例程展示了LCDC的缩放功能，图片缩小和恢复交替显示。

2、使用环境

    软件开发环境：KEIL MDK-ARM V5.34
                  IAR EWARM 8.50.1 
    芯片支持：
        N32H730  
        N32H735   
        N32H735EC
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787
        
3、使用说明

    系统配置
        1、时钟源：HSI+PLL
        2、系统时钟频率：
            600MHz
        3、GPIO：
            以下端口硬件基于N32H787_HMI_V1.1
            PI15: R0, PJ0: R1, PJ1: R2, PJ2: R3, PJ3: R4, PJ4: R5, PJ5: R6, PJ6: R7,
            PJ7: G0, PJ8: G1, PJ9: G2, PJ10: G3, PJ11: G4, PK0: G5, PI11: G6, PD3: G7,
            PJ12: B0, PJ13: B1, PJ14: B2, PJ15: B3, PK3: B4, PK4: B5, PA15: B6, PB9: B7,
            PG7: LCD_CLK, PI12: LCD_HSYNC, PI13: LCD_VSYNC, PK7: LCD_DE, PB10: LCD_BL, PH3: LCD_DIS.
        3、LCD：
            ATK-MD0700R-800480

    使用方法：
        1、编译后将程序下载到开发板并复位运行。
        2、可观察到图片不断的缩小并恢复。

4、注意事项
        如果需要使用M4内核，用户需要添加配置
    
1. Function description

    This example demonstrates the scaling function of the LCDC, where the image alternately zooms out and restores to its original size.

2. Use environment

    Software development environment: KEIL MDK-ARM V5.34
                                      IAR EWARM 8.50.1 
    Supported chips:
        N32H730  
        N32H735   
        N32H735EC
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787

3. Instructions for use

    System Configuration:
        1. Clock source: HSI+PLL
        2. System Clock frequency: 
            600MHz
        3.GPIO:
            The following port hardware is based on N32H787_HMI_V1.1
            PI15: R0, PJ0: R1, PJ1: R2, PJ2: R3, PJ3: R4, PJ4: R5, PJ5: R6, PJ6: R7,
            PJ7: G0, PJ8: G1, PJ9: G2, PJ10: G3, PJ11: G4, PK0: G5, PI11: G6, PD3: G7,
            PJ12: B0, PJ13: B1, PJ14: B2, PJ15: B3, PK3: B4, PK4: B5, PA15: B6, PB9: B7,
            PG7: LCD_CLK, PI12: LCD_HSYNC, PI13: LCD_VSYNC, PK7: LCD_DE, PB10: LCD_BL, PH3: LCD_DIS.
        3、LCD：
            ATK-MD0700R-800480

     Instructions:
        1. After compiling, download the program and reset, the program start running.
        2. It can be observed that the image alternately zooms out and restores to its original size.

4. Attention
       If need to use the M4 kernel, you need to add the configuration.

