1、功能说明
    1、读写 SRAM IS61WV102416FALL-20TLI

2、使用环境

    软件开发环境：KEIL MDK-ARM V5.34
                          IAR EWARM 8.50.1
                  
    芯片支持：
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787
    开发板支持：
        N32H787_EVB

3、使用说明
    
    系统配置:
        1、时钟源： HSI+PLL
        2、系统时钟频率：
            M7核 : 600MHz 
        3、串口配置：
                    - 串口为USART1（TX：PA9  RX：PA10）:
                    - 数据位：8
                    - 停止位：1
                    - 奇偶校验：无
                    - 波特率： 115200 
        4、GPIO配置：
                D0:PD14     D1:PD15     D2:PD0      D3:PD1
                D4:PE7      D5:PE8      D6:PE9      D7:PE10
                D8:PE11     D9:PA5      D10:PE13    D11:PE14
                D12:PC0     D13:PD8     D14:PD9     D15:PD10
                
                A0:PF0      A1:PF1      A2:PF2      A3:PF3
                A4:PF4      A5:PF5      A6:PF12     A7:PF13
                A8:PF14     A9:PF15     A10:PG0     A11:PG1
                A12:PG2     A13:PG3     A14:PG4     A15:PG5
                A16:PD11    A17:PD12    A18:PD13    A19:PE3

                NOE:PD4     NWE:PD5     NE3:PG10
                NBL0:PE0    NBL1:PE1

    使用方法：
        编译后烧录到评估板，上电，串口打印 SRAM 读写结果

4、注意事项
    无
    

1. Function description
    Read, write SRAM IS61WV102416FALL-20TLI

2. Development environment

    Software development environment: KEIL MDK-ARM V5.34
                                                             IAR EWARM 8.50.1

    MCU support:
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787
    Development board support：
        N32H787_EVB


3. How to use

    System configuration:
        1. Clock source: HSI+PLL
        2. System Clock frequency: 
            M7 Core：600MHz 
        3. Serial port configuration:

                            - Serial port: USART1 (TX: PA9 RX: PA10) :
                            - Data bit: 8
                            - Stop bit: 1
                            - Parity check: None
                            - Baud rate: 115200
                            
        4. GPIO configuration：
                D0:PD14     D1:PD15     D2:PD0      D3:PD1
                D4:PE7      D5:PE8      D6:PE9      D7:PE10
                D8:PE11     D9:PA5      D10:PE13    D11:PE14
                D12:PC0     D13:PD8     D14:PD9     D15:PD10
                
                A0:PF0      A1:PF1      A2:PF2      A3:PF3
                A4:PF4      A5:PF5      A6:PF12     A7:PF13
                A8:PF14     A9:PF15     A10:PG0     A11:PG1
                A12:PG2     A13:PG3     A14:PG4     A15:PG5
                A16:PD11    A17:PD12    A18:PD13    A19:PE3

                NOE:PD4     NWE:PD5     NE3:PG10
                NBL0:PE0    NBL1:PE1

    Instructions:
        After compiling, burn it to the evaluation board, power it on, and print the SRAM read-write results through the serial port

4. Attention
    None

