1、功能说明
    1、读写擦Nor Flash S29GL01GS11TF1020

2、使用环境

    软件开发环境：KEIL MDK-ARM V5.34
                  IAR EWARM 8.50.1 
    芯片支持：
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787
    开发板支持：
        无


3、使用说明
    
    系统配置:
        1、FEMC时钟源：AHB
        2、串口配置：
                - 串口为USART1（TX：PA9  RX：PA10）:
                - 数据位：8
                - 停止位：1
                - 奇偶校验：无
                - 波特率： 115200 
                    
        3、GPIO配置：
                D0:PD14     D1:PD15     D2:PJ6      D3:PJ7
                D4:PE7      D5:PE8      D6:PE9      D7:PE10
                D8:PE11     D9:PE12     D10:PE13    D11:PE14
                D12:PE15    D13:PD8     D14:PD9     D15:PD10
                
                A0:PF0      A1:PF1      A2:PF2      A3:PF3
                A4:PF4      A5:PF5      A6:PF12     A7:PF13
                A8:PF14     A9:PF15     A10:PG0     A11:PG1
                A12:PG2     A13:PG3     A14:PG4     A15:PG5
                A16:PD11    A17:PD12    A18:PD13    A19:PE3
                A20:PE4     A21:PE5     A22:PE6     A23:PE2
                A24:PG13    A25:PG14
                
                NOE:PD4     NWE:PD5     NE:PG9      NWAIT:PD6
                
    使用方法：
        编译后烧录到评估板，上电，串口打印Nor Flash 读写擦结果

4、注意事项
    没有开发板支持Nor-Flash
    

1. Function description
    Read, write and erase NOR Flash S29GL01GS11TF1020

2. Development environment

    Software development environment: KEIL MDK-ARM V5.34
                                      IAR EWARM 8.50.1 
    MCU support:
        N32H760
        N32H762
        N32H765
        N32H765EC
        N32H785
        N32H785EC
        N32H787
    Development board support：
       None

3. How to use

    System configuration:
        1. FEMC clock source: AHB
        2. Serial port configuration:
                - Serial port: USART1 (TX: PA9 RX: PA10) :
                - Data bit: 8
                - Stop bit: 1
                - Parity check: None
                - Baud rate: 115200
                
        3. GPIO configuration：
                D0:PD14     D1:PD15     D2:PJ6      D3:PJ7
                D4:PE7      D5:PE8      D6:PE9      D7:PE10
                D8:PE11     D9:PE12     D10:PE13    D11:PE14
                D12:PE15    D13:PD8     D14:PD9     D15:PD10
                
                A0:PF0      A1:PF1      A2:PF2      A3:PF3
                A4:PF4      A5:PF5      A6:PF12     A7:PF13
                A8:PF14     A9:PF15     A10:PG0     A11:PG1
                A12:PG2     A13:PG3     A14:PG4     A15:PG5
                A16:PD11    A17:PD12    A18:PD13    A19:PE3
                A20:PE4     A21:PE5     A22:PE6     A23:PE2
                A24:PG13    A25:PG14
                
                NOE:PD4     NWE:PD5     NE:PG9      NWAIT:PD6

    Instructions:
        After compiling, burn it to the evaluation board, power it on, and print the Nor Flash read-write-erase results through the serial port

4. Attention
    No development board supports Nor-Flash

